fix typos

docs/docs/configuration/advanced/reference.md

@@ -339,7 +339,7 @@ detect:
   # especially when using separate streams for detect and record.
   # Use this setting to make the timeline bounding boxes more closely align
   # with the recording. The value can be positive or negative.
-  # TIP: Imagine there is an tracked object clip with a person walking from left to right.
+  # TIP: Imagine there is a tracked object clip with a person walking from left to right.
   #      If the tracked object lifecycle bounding box is consistently to the left of the person
   #      then the value should be decreased. Similarly, if a person is walking from
   #      left to right and the bounding box is consistently ahead of the person

docs/docs/configuration/audio_detectors.md

@@ -78,7 +78,7 @@ cameras:
 
 ### Configuring Minimum Volume
 
-The audio detector uses volume levels in the same way that motion in a camera feed is used for object detection. This means that Frigate will not run audio detection unless the audio volume is above the configured level in order to reduce resource usage. Audio levels can vary widely between camera models so it is important to run tests to see what volume levels are. The [Debug view](/usage/live#the-single-camera-view) in the Frigate UI has an Audio tab for cameras that have the `audio` role assigned where a graph and the current levels are is displayed. The `min_volume` parameter should be set to the minimum the `RMS` level required to run audio detection.
+The audio detector uses volume levels in the same way that motion in a camera feed is used for object detection. This means that Frigate will not run audio detection unless the audio volume is above the configured level in order to reduce resource usage. Audio levels can vary widely between camera models so it is important to run tests to see what volume levels are. The [Debug view](/usage/live#the-single-camera-view) in the Frigate UI has an Audio tab for cameras that have the `audio` role assigned where a graph and the current levels are displayed. The `min_volume` parameter should be set to the minimum the `RMS` level required to run audio detection.
 
 :::tip
 

docs/docs/configuration/autotracking.md

@@ -6,6 +6,7 @@ title: Camera Autotracking
 import ConfigTabs from "@site/src/components/ConfigTabs";
 import TabItem from "@theme/TabItem";
 import NavPath from "@site/src/components/NavPath";
+import FaqItem from "@site/src/components/FaqItem";
 
 An ONVIF-capable, PTZ (pan-tilt-zoom) camera that supports relative movement within the field of view (FOV) can be configured to automatically track moving objects and keep them in the center of the frame.
 
@@ -187,30 +188,96 @@ In security and surveillance, it's common to use "spotter" cameras in combinatio
 
 ## Troubleshooting and FAQ
 
-### The autotracker loses track of my object. Why?
+### Camera Compatibility
+
+<FaqItem id="which-ptz-camera-should-i-use-for-autotracking" question="Which PTZ camera should I use for autotracking?">
+
+See the community-maintained list of [ONVIF PTZ camera recommendations](cameras.md#onvif-ptz-camera-recommendations) for cameras and brands reported to work (and not work) with autotracking. This is not an exhaustive list that is frequently updated, so other cameras not listed may also work well. Frigate's autotracking was developed with a Dahua SD1A404XB-GNR (now sold as the EmpireTech PTZ1A4M-4X-S2), and Dahua / EmpireTech PTZs are the most consistently reported as working well.
+
+When comparing models:
+
+- Verify ONVIF support first. See [Checking ONVIF camera support](#checking-onvif-camera-support) above.
+- Favor a camera with a fast PTZ motor. Cameras with slow motors may fail [calibration](#calibration) and will struggle to keep up with objects that move across the field of view quickly.
+
+</FaqItem>
+
+<FaqItem id="does-autotracking-work-with-reolink-ptz-cameras" question="Does autotracking work with Reolink PTZ cameras?">
+
+No. Reolink cameras (including the TrackMix series) lack the ONVIF FOV RelativeMove firmware support that Frigate's autotracker requires, so autotracking will not work with any current Reolink PTZ. Their video streams and basic PTZ controls still work in Frigate. If you want object tracking on a Reolink PTZ, you will need to use the tracking feature built into the camera's firmware, which is proprietary and operates independently of Frigate.
+
+</FaqItem>
+
+<FaqItem id="im-seeing-an-error-in-the-logs-that-my-camera-is-still-in-onvif-moving-status-what-does-this-mean" question={"I'm seeing an error in the logs that my camera \"is still in ONVIF 'MOVING' status.\" What does this mean?"}>
+
+There are two possible known reasons for this (and perhaps others yet unknown): a slow PTZ motor or buggy camera firmware. Frigate uses an ONVIF parameter provided by the camera, `MoveStatus`, to determine when the PTZ's motor is moving or idle. According to some users, Hikvision PTZs (even with the latest firmware), are not updating this value after PTZ movement. Unfortunately there is no workaround to this bug in Hikvision firmware, so autotracking will not function correctly and should be disabled in your config. This may also be the case with other non-Hikvision cameras utilizing Hikvision firmware, such as some Annke models. In rare cases the vendor may provide fixed firmware on request; for example, Annke has supplied firmware that resolves this for the CZ504 (see the [camera recommendations list](cameras.md#onvif-ptz-camera-recommendations)).
+
+</FaqItem>
+
+<FaqItem id="calibration-seems-to-have-completed-but-the-camera-is-not-actually-moving-to-track-my-object-why" question="Calibration seems to have completed, but the camera is not actually moving to track my object. Why?">
+
+Some cameras have firmware that reports that FOV RelativeMove, the ONVIF command that Frigate uses for autotracking, is supported. However, if the camera does not pan or tilt when an object comes into the required zone, your camera's firmware does not actually support FOV RelativeMove. One such camera is the Uniview IPC672LR-AX4DUPK. It actually moves its zoom motor instead of panning and tilting and does not follow the ONVIF standard whatsoever.
+
+</FaqItem>
+
+### Calibration Issues
+
+<FaqItem id="i-tried-calibrating-my-camera-but-the-logs-show-that-it-is-stuck-at-0-and-frigate-is-not-starting-up" question="I tried calibrating my camera, but the logs show that it is stuck at 0% and Frigate is not starting up.">
+
+This is often caused by the same reason as the "MOVING" status error above - the `MoveStatus` ONVIF parameter is not changing due to a bug in your camera's firmware. Also, see the note above: Frigate's web UI and all other cameras will be unresponsive while calibration is in progress. This is expected and normal. But if you don't see log entries every few seconds for calibration progress, your camera is not compatible with autotracking.
+
+</FaqItem>
+
+<FaqItem id="frigate-reports-an-error-saying-that-calibration-has-failed-why" question="Frigate reports an error saying that calibration has failed. Why?">
+
+Calibration measures the amount of time it takes for Frigate to make a series of movements with your PTZ. This error message is recorded in the log if these values are too high for Frigate to support calibrated autotracking. This is often the case when your camera's motor or network connection is too slow or your camera's firmware doesn't report the motor status in a timely manner.
+
+Some things to try:
+
+- If your camera's firmware has a PTZ or motor speed setting, set it to the fastest available speed and calibrate again.
+- Run without calibration: remove the `movement_weights` line from your config, set `calibrate_on_startup` to `False`, and restart.
+
+If calibration consistently fails, this often means your camera's motor is too slow and autotracking will behave unpredictably or won't be able to keep up with moving objects.
+
+</FaqItem>
+
+<FaqItem id="autotracking-is-erratic-or-moves-the-camera-in-the-wrong-direction" question="Autotracking is erratic, moves the camera in the wrong direction, or zooms past my object. Why?">
+
+Frigate uses the `movement_weights` measured during calibration to predict how far the camera needs to move to keep an object centered, so inaccurate values produce movements that don't seem to make sense: overshooting, moving the opposite direction, or zooming in on an object's last known position and losing it entirely. This is almost always a calibration issue.
+
+- Remove the `movement_weights` entry from your config and restart Frigate to run without calibration. If tracking improves, try recalibrating.
+- Recalibrate several times. The `movement_weights` values should be close to each other after each run. If they vary significantly between runs, your camera may not be reporting its motor status reliably, and you may get better results without calibration.
+- If you are using zooming, a high `zoom_factor` can cause the camera to zoom in too far and lose the object. Try a lower value.
+
+Remember to recalibrate whenever you change your `return_preset`, change your camera's detect `fps`, or enable zooming after calibrating with it disabled.
+
+</FaqItem>
+
+### Tracking Behavior
+
+<FaqItem id="the-autotracker-loses-track-of-my-object-why" question="The autotracker loses track of my object. Why?">
 
 There are many reasons this could be the case. If you are using experimental zooming, your `zoom_factor` value might be too high, the object might be traveling too quickly, the scene might be too dark, there are not enough details in the scene (for example, a PTZ looking down on a driveway or other monotone background without a sufficient number of hard edges or corners), or the scene is otherwise less than optimal for Frigate to maintain tracking.
 
 Your camera's shutter speed may also be set too low so that blurring occurs with motion. Check your camera's firmware to see if you can increase the shutter speed.
 
-Watching Frigate's debug view can help to determine a possible cause. The autotracked object will have a thicker colored box around it.
+Watching Frigate's debug view can help to determine a possible cause. The autotracked object will have a thicker colored box around it. If the camera consistently zooms in on the object and then loses it, see [Autotracking is erratic, moves the camera in the wrong direction, or zooms past my object. Why?](#autotracking-is-erratic-or-moves-the-camera-in-the-wrong-direction) above.
 
-### I'm seeing an error in the logs that my camera "is still in ONVIF 'MOVING' status." What does this mean?
+</FaqItem>
 
-There are two possible known reasons for this (and perhaps others yet unknown): a slow PTZ motor or buggy camera firmware. Frigate uses an ONVIF parameter provided by the camera, `MoveStatus`, to determine when the PTZ's motor is moving or idle. According to some users, Hikvision PTZs (even with the latest firmware), are not updating this value after PTZ movement. Unfortunately there is no workaround to this bug in Hikvision firmware, so autotracking will not function correctly and should be disabled in your config. This may also be the case with other non-Hikvision cameras utilizing Hikvision firmware.
-
-### I tried calibrating my camera, but the logs show that it is stuck at 0% and Frigate is not starting up.
-
-This is often caused by the same reason as above - the `MoveStatus` ONVIF parameter is not changing due to a bug in your camera's firmware. Also, see the note above: Frigate's web UI and all other cameras will be unresponsive while calibration is in progress. This is expected and normal. But if you don't see log entries every few seconds for calibration progress, your camera is not compatible with autotracking.
-
-### I'm seeing this error in the logs: "Autotracker: motion estimator couldn't get transformations". What does this mean?
+<FaqItem id="im-seeing-this-error-in-the-logs-autotracker-motion-estimator-couldnt-get-transformations-what-does-this-mean" question={"I'm seeing this error in the logs: \"Autotracker: motion estimator couldn't get transformations\". What does this mean?"}>
 
 To maintain object tracking during PTZ moves, Frigate tracks the motion of your camera based on the details of the frame. If you are seeing this message, it could mean that your `zoom_factor` may be set too high, the scene around your detected object does not have enough details (like hard edges or color variations), or your camera's shutter speed is too slow and motion blur is occurring. Try reducing `zoom_factor`, finding a way to alter the scene around your object, or changing your camera's shutter speed.
 
-### Calibration seems to have completed, but the camera is not actually moving to track my object. Why?
+</FaqItem>
 
-Some cameras have firmware that reports that FOV RelativeMove, the ONVIF command that Frigate uses for autotracking, is supported. However, if the camera does not pan or tilt when an object comes into the required zone, your camera's firmware does not actually support FOV RelativeMove. One such camera is the Uniview IPC672LR-AX4DUPK. It actually moves its zoom motor instead of panning and tilting and does not follow the ONVIF standard whatsoever.
+<FaqItem id="why-does-object-detection-pause-briefly-when-the-camera-moves" question="Why does object detection pause briefly when the camera moves?">
 
-### Frigate reports an error saying that calibration has failed. Why?
+When the PTZ moves, the entire frame changes at once. Frigate's motion detection treats sudden scene-wide changes (like a lightning flash, an infrared mode switch, or a camera move) specially and pauses detection momentarily until the scene stabilizes. This is expected and normal, and detection resumes shortly after the camera stops moving. If detection does not resume once the camera is stationary, use the [debug view](/usage/live#the-single-camera-view) to see what is happening.
 
-Calibration measures the amount of time it takes for Frigate to make a series of movements with your PTZ. This error message is recorded in the log if these values are too high for Frigate to support calibrated autotracking. This is often the case when your camera's motor or network connection is too slow or your camera's firmware doesn't report the motor status in a timely manner. You can try running without calibration (just remove the `movement_weights` line from your config and restart), but if calibration fails, this often means that autotracking will behave unpredictably.
+</FaqItem>
+
+<FaqItem id="can-i-turn-autotracking-on-and-off-automatically" question="Can I turn autotracking on and off automatically?">
+
+Yes. Autotracking can be toggled per camera at runtime over MQTT with the [`frigate/<camera_name>/ptz_autotracker/set`](../integrations/mqtt.md#frigatecamera_nameptz_autotrackerset) topic, and the [Home Assistant integration](../integrations/home-assistant.md) exposes a switch for it. This pairs well with the "spotter" camera automations described in [Usage applications](#usage-applications) above, for example only enabling autotracking at night or when nobody is home.
+
+</FaqItem>

docs/docs/configuration/face_recognition.md

@@ -262,7 +262,7 @@ Face recognition does not run on the recording stream, this would be suboptimal
 
 <FaqItem id="detection-does-not-work-well-with-blurry-images" question="Detection does not work well with blurry images?">
 
-Accuracy is definitely a going to be improved with higher quality cameras / streams. It is important to look at the DORI (Detection Observation Recognition Identification) range of your camera, if that specification is posted. This specification explains the distance from the camera that a person can be detected, observed, recognized, and identified. The identification range is the most relevant here, and the distance listed by the camera is the furthest that face recognition will realistically work.
+Accuracy is definitely going to be improved with higher quality cameras / streams. It is important to look at the DORI (Detection Observation Recognition Identification) range of your camera, if that specification is posted. This specification explains the distance from the camera that a person can be detected, observed, recognized, and identified. The identification range is the most relevant here, and the distance listed by the camera is the furthest that face recognition will realistically work.
 
 Some users have also noted that setting the stream in camera firmware to a constant bit rate (CBR) leads to better image clarity than with a variable bit rate (VBR).
 
@@ -324,7 +324,7 @@ This also applies to a stranger who is repeatedly matched to a known person (for
 
 <FaqItem id="i-see-scores-above-the-threshold-in-the-recent-recognitions-tab-but-a-sub-label-wasnt-assigned" question="I see scores above the threshold in the Recent Recognitions tab, but a sub label wasn't assigned?">
 
-The Frigate considers the recognition scores across all recognition attempts for each person object. The scores are continually weighted based on the area of the face, and a sub label will only be assigned to person if a person is confidently recognized consistently. This avoids cases where a single high confidence recognition would throw off the results.
+Frigate considers the recognition scores across all recognition attempts for each person object. The scores are continually weighted based on the area of the face, and a sub label will only be assigned to person if a person is confidently recognized consistently. This avoids cases where a single high confidence recognition would throw off the results.
 
 </FaqItem>
 

docs/docs/configuration/go2rtc.md

@@ -67,4 +67,4 @@ If your stream won't play, has no audio, uses excessive CPU, or otherwise misbeh
 
 ## Homekit Configuration
 
-To add camera streams to Homekit Frigate must be configured in docker to use `host` networking mode. Once that is done, you can use the go2rtc WebUI (accessed via port 1984, which is disabled by default) to share export a camera to Homekit. Any changes made will automatically be saved to `/config/go2rtc_homekit.yml`.
+To add camera streams to Homekit Frigate must be configured in docker to use `host` networking mode. Once that is done, you can use the go2rtc WebUI (accessed via port 1984, which is disabled by default) to export a camera to Homekit. Any changes made will automatically be saved to `/config/go2rtc_homekit.yml`.

docs/docs/configuration/motion_detection.md

@@ -66,7 +66,7 @@ motion:
 </TabItem>
 </ConfigTabs>
 
-Lower values mean motion detection is more sensitive to changes in color, making it more likely for example to detect motion when a brown dogs blends in with a brown fence or a person wearing a red shirt blends in with a red car. If the threshold is too low however, it may detect things like grass blowing in the wind, shadows, etc. to be detected as motion.
+Lower values mean motion detection is more sensitive to changes in color, making it more likely for example to detect motion when a brown dog blends in with a brown fence or a person wearing a red shirt blends in with a red car. If the threshold is too low however, it may detect things like grass blowing in the wind, shadows, etc. to be detected as motion.
 
 Watching the motion boxes in the debug view, increase the threshold until you only see motion that is visible to the eye. Once this is done, it is important to test and ensure that desired motion is still detected.
 

docs/docs/configuration/object_detectors.md

@@ -725,7 +725,7 @@ The inference time was determined on a rk3588 with 3 NPU cores.
 
 To convert a onnx model to the rknn format using the [rknn-toolkit2](https://github.com/airockchip/rknn-toolkit2/) you have to:
 
-- Place one ore more models in onnx format in the directory `config/model_cache/rknn_cache/onnx` on your docker host (this might require `sudo` privileges).
+- Place one or more models in onnx format in the directory `config/model_cache/rknn_cache/onnx` on your docker host (this might require `sudo` privileges).
 - Save the configuration file under `config/conv2rknn.yaml` (see below for details).
 - Run `docker exec <frigate_container_id> python3 /opt/conv2rknn.py`. If the conversion was successful, the rknn models will be placed in `config/model_cache/rknn_cache`.
 

docs/docs/configuration/object_filters.md

@@ -36,7 +36,7 @@ Any detection below `min_score` will be immediately thrown out and never tracked
 
 ### Threshold
 
-`threshold` is used to determine that the object is a true positive. Once an object is detected with a score >= `threshold` object is considered a true positive. If `threshold` is too low then some higher scoring false positives may create an tracked object. If `threshold` is too high then true positive tracked objects may be missed due to the object never scoring high enough.
+`threshold` is used to determine that the object is a true positive. Once an object is detected with a score >= `threshold` object is considered a true positive. If `threshold` is too low then some higher scoring false positives may create a tracked object. If `threshold` is too high then true positive tracked objects may be missed due to the object never scoring high enough.
 
 ## Configuring Object Scores
 

docs/docs/configuration/semantic_search.md

@@ -226,7 +226,7 @@ For tips on getting the best results from Semantic Search (choosing between thum
 
 ## Triggers
 
-Triggers utilize Semantic Search to automate actions when a tracked object matches a specified image or description. Triggers can be configured so that Frigate executes a specific actions when a tracked object's image or description matches a predefined image or text, based on a similarity threshold. Triggers are managed per camera and can be configured via the Frigate UI in the Settings page under the Triggers tab.
+Triggers utilize Semantic Search to automate actions when a tracked object matches a specified image or description. Triggers can be configured so that Frigate executes specific actions when a tracked object's image or description matches a predefined image or text, based on a similarity threshold. Triggers are managed per camera and can be configured via the Frigate UI in the Settings page under the Triggers tab.
 
 :::note
 

docs/docs/configuration/stationary_objects.md

@@ -61,4 +61,4 @@ Now you have to determine which of the bounding boxes in this frame should be ma
 
 Now let's assume that those other 3 cars were already being tracked as stationary objects, so the car driving down the street is a new 4th car. The object tracker knows we have had 3 cars and we now have 4. As the new car approaches the parked cars, the bounding boxes for all 4 cars is predicted based on the previous frames. The predicted boxes for the parked cars is pretty much a 100% overlap with the bounding boxes in the new frame. The parked cars are slam dunk matches to the tracking ids they had before and the only one left is the remaining bounding box which gets assigned to the new car. This results in a much lower error rate. Not perfect, but better.
 
-The most difficult scenario that causes IDs to be assigned incorrectly is when an object completely occludes another object. When a car drives in front of another car and its no longer visible, a bounding box disappeared and it's a bit of a toss up when assigning the id since it's difficult to know which one is in front of the other. This happens for cars passing in front of other cars fairly often. It's something that we want to improve in the future.
+The most difficult scenario that causes IDs to be assigned incorrectly is when an object completely occludes another object. When a car drives in front of another car and it's no longer visible, a bounding box disappeared and it's a bit of a toss up when assigning the id since it's difficult to know which one is in front of the other. This happens for cars passing in front of other cars fairly often. It's something that we want to improve in the future.

docs/docs/frigate/installation.md

@@ -94,7 +94,7 @@ The following sections contain additional setup steps that are only required if
 
 By default, the Raspberry Pi limits the amount of memory available to the GPU. In order to use ffmpeg hardware acceleration, you must increase the available memory by setting `gpu_mem` to the maximum recommended value in `config.txt` as described in the [official docs](https://www.raspberrypi.org/documentation/computers/config_txt.html#memory-options).
 
-Additionally, the USB Coral draws a considerable amount of power. If using any other USB devices such as an SSD, you will experience instability due to the Pi not providing enough power to USB devices. You will need to purchase an external USB hub with it's own power supply. Some have reported success with <a href="https://amzn.to/3a2mH0P" target="_blank" rel="nofollow noopener sponsored">this</a> (affiliate link).
+Additionally, the USB Coral draws a considerable amount of power. If using any other USB devices such as an SSD, you will experience instability due to the Pi not providing enough power to USB devices. You will need to purchase an external USB hub with its own power supply. Some have reported success with <a href="https://amzn.to/3a2mH0P" target="_blank" rel="nofollow noopener sponsored">this</a> (affiliate link).
 
 ### Hailo-8
 

docs/docs/integrations/third_party_extensions.md

@@ -23,7 +23,7 @@ The [Advanced Camera Card](https://card.camera/#/README) is a Home Assistant das
 
 ## [Double Take](https://github.com/skrashevich/double-take)
 
-[Double Take](https://github.com/skrashevich/double-take) provides an unified UI and API for processing and training images for facial recognition.
+[Double Take](https://github.com/skrashevich/double-take) provides a unified UI and API for processing and training images for facial recognition.
 It supports automatically setting the sub labels in Frigate for person objects that are detected and recognized.
 This is a fork (with fixed errors and new features) of [original Double Take](https://github.com/jakowenko/double-take) project which, unfortunately, isn't being maintained by author.
 
@@ -53,7 +53,7 @@ This is a fork (with fixed errors and new features) of [original Double Take](ht
 
 ## [Scrypted - Frigate bridge plugin](https://github.com/apocaliss92/scrypted-frigate-bridge)
 
-[Scrypted - Frigate bridge](https://github.com/apocaliss92/scrypted-frigate-bridge) is an plugin that allows to ingest Frigate detections, motion, videoclips on Scrypted as well as provide templates to export rebroadcast configurations on Frigate.
+[Scrypted - Frigate bridge](https://github.com/apocaliss92/scrypted-frigate-bridge) is a plugin that allows you to ingest Frigate detections, motion, videoclips on Scrypted as well as provide templates to export rebroadcast configurations on Frigate.
 
 ## [Strix](https://github.com/eduard256/Strix)
 

docs/docs/plus/annotating.md

@@ -19,7 +19,7 @@ For the best results, follow these guidelines. You may also want to review the d
 
 ## AI suggested labels
 
-If you have an active Frigate+ subscription, new uploads will be scanned for the objects configured for you camera and you will see suggested labels as light blue boxes when annotating in Frigate+. These suggestions are processed via a queue and typically complete within a minute after uploading, but processing times can be longer.
+If you have an active Frigate+ subscription, new uploads will be scanned for the objects configured for your camera and you will see suggested labels as light blue boxes when annotating in Frigate+. These suggestions are processed via a queue and typically complete within a minute after uploading, but processing times can be longer.
 
 ![Suggestions](/img/plus/suggestions.webp)
 

docs/docs/troubleshooting/edgetpu.md

@@ -12,7 +12,7 @@ There are many possible causes for a USB coral not being detected and some are O
 
 :::tip
 
-Using `lsusb` or checking the hardware page in HA OS will show as `1a6e:089a Global Unichip Corp.` until Frigate runs an inferance using the coral. So don't worry about the identification until after Frigate has attempted to detect the coral.
+Using `lsusb` or checking the hardware page in HA OS will show as `1a6e:089a Global Unichip Corp.` until Frigate runs an inference using the coral. So don't worry about the identification until after Frigate has attempted to detect the coral.
 
 :::
 
@@ -43,13 +43,13 @@ Some users have reported that this older device runs an older kernel causing iss
 3. Start the docker container with Coral TPU enabled in the config
 4. The TPU would be detected but a few moments later it would disconnect.
 5. While leaving the TPU device plugged in, restart the NAS using the reboot command in the UI. Do NOT unplug the NAS/power it off etc.
-6. Open the control panel - info scree. The coral TPU will now be recognised as a USB Device - google inc
+6. Open the control panel - info screen. The coral TPU will now be recognized as a USB Device - google inc
 7. Start the frigate container. Everything should work now!
 
 ### QNAP NAS
 
 QNAP NAS devices, such as the TS-253A, may use connected Coral TPU devices if [QuMagie](https://www.qnap.com/en/software/qumagie) is installed along with its QNAP AI Core extension. If any of the features (`facial recognition`, `object recognition`, or `similar photo recognition`) are enabled, Container Station applications such as `Frigate` or `CodeProject.AI Server` will be unable to initialize the TPU device in use.
-To allow the Coral TPU device to be discovered, the you must either:
+To allow the Coral TPU device to be discovered, you must either:
 
 1. [Disable the AI recognition features in QuMagie](https://docs.qnap.com/application/qumagie/2.x/en-us/configuring-qnap-ai-core-settings-FB13CE03.html),
 2. Remove the QNAP AI Core extension or
@@ -87,7 +87,7 @@ dtoverlay=pcie-32bit-dma-pi5
 
 ## Only One PCIe Coral Is Detected With Coral Dual EdgeTPU
 
-Coral Dual EdgeTPU is one card with two identical TPU cores. Each core has it's own PCIe interface and motherboard needs to have two PCIe busses on the m.2 slot to make them both work.
+Coral Dual EdgeTPU is one card with two identical TPU cores. Each core has its own PCIe interface and motherboard needs to have two PCIe busses on the m.2 slot to make them both work.
 
 E-key slot implemented to full m.2 electromechanical specification has two PCIe busses. Most motherboard manufacturers implement only one PCIe bus in m.2 E-key connector (this is why only one TPU is working). Some SBCs can have only USB bus on m.2 connector, ie none of TPUs will work.
 

docs/docs/troubleshooting/faqs.md

@@ -29,7 +29,7 @@ You can open `chrome://media-internals/` in another tab and then try to playback
 
 ### What do I do if my cameras sub stream is not good enough?
 
-Frigate generally [recommends cameras with configurable sub streams](/frigate/hardware.md). However, if your camera does not have a sub stream that a suitable resolution, the main stream can be resized.
+Frigate generally [recommends cameras with configurable sub streams](/frigate/hardware.md). However, if your camera does not have a sub stream that is a suitable resolution, the main stream can be resized.
 
 To do this efficiently the following setup is required:
 

docs/docs/usage/live.md

@@ -60,7 +60,7 @@ You can optionally overlay live streaming statistics (stream type, bandwidth, la
 
 Right-clicking (or long-pressing) a camera tile opens a context menu with quick controls: an **audio volume** control for streams that support audio, **Mute / Unmute all cameras**, **show or hide streaming statistics**, the **debug view**, **notification** options, and, for admins, turning the camera on or off. If the audio control doesn't appear, see [Audio Support](/configuration/live#audio-support). Audio requires go2rtc configured with a compatible codec.
 
-A **Low-bandwidth mode** notice may also appear in the context menu with a **Reset** option appears when Frigate has fallen back to the lower-quality jsmpeg stream. See the [Live view FAQ](/configuration/live#live-view-faq) for why this happens.
+A **Low-bandwidth mode** notice may also appear in the context menu with a **Reset** option when Frigate has fallen back to the lower-quality jsmpeg stream. See the [Live view FAQ](/configuration/live#live-view-faq) for why this happens.
 
 For non-default groups, the context menu also exposes **Streaming Settings** for that camera, which let you choose:
 

web/public/locales/en/views/settings.json

@@ -1053,7 +1053,7 @@
       },
       "createUser": {
         "title": "Create New User",
-        "desc": "Add a new user account and specify an role for access to areas of the Frigate UI.",
+        "desc": "Add a new user account and specify a role for access to areas of the Frigate UI.",
         "usernameOnlyInclude": "Username may only include letters, numbers, . or _",
         "confirmPassword": "Please confirm your password"
       },