Update hailo docs installation

docs/docs/frigate/installation.md

@@ -106,14 +106,107 @@ The Hailo-8 and Hailo-8L AI accelerators are available in both M.2 and HAT form
 
 #### Installation
 
-For Raspberry Pi 5 users with the AI Kit, installation is straightforward. Simply follow this [guide](https://www.raspberrypi.com/documentation/accessories/ai-kit.html#ai-kit-installation) to install the driver and software.
+:::warning
 
-For other installations, follow these steps for installation:
+The Raspberry Pi kernel includes an older version of the Hailo driver that is incompatible with Frigate. You **must** follow the installation steps below to install the correct driver version, and you **must** disable the built-in kernel driver as described in step 1.
 
-1. Install the driver from the [Hailo GitHub repository](https://github.com/hailo-ai/hailort-drivers). A convenient script for Linux is available to clone the repository, build the driver, and install it.
-2. Copy or download [this script](https://github.com/blakeblackshear/frigate/blob/dev/docker/hailo8l/user_installation.sh).
-3. Ensure it has execution permissions with `sudo chmod +x user_installation.sh`
-4. Run the script with `./user_installation.sh`
+:::
+
+1. **Disable the built-in Hailo driver (Raspberry Pi only)**:
+
+   :::note
+
+   If you are **not** using a Raspberry Pi, skip this step and proceed directly to step 2.
+
+   :::
+
+   If you are using a Raspberry Pi, you need to blacklist the built-in kernel Hailo driver to prevent conflicts. First, check if the driver is currently loaded:
+
+   ```bash
+   lsmod | grep hailo
+   ```
+
+   If it shows `hailo_pci`, unload it:
+
+   ```bash
+   sudo rmmod hailo_pci
+   ```
+
+   Now blacklist the driver to prevent it from loading on boot:
+
+   ```bash
+   echo "blacklist hailo_pci" | sudo tee /etc/modprobe.d/blacklist-hailo_pci.conf
+   ```
+
+   Update initramfs to ensure the blacklist takes effect:
+
+   ```bash
+   sudo update-initramfs -u
+   ```
+
+   Reboot your Raspberry Pi:
+
+   ```bash
+   sudo reboot
+   ```
+
+   After rebooting, verify the built-in driver is not loaded:
+
+   ```bash
+   lsmod | grep hailo
+   ```
+
+   This command should return no results. If it still shows `hailo_pci`, the blacklist did not take effect properly and you may need to check for other Hailo packages installed via apt that are loading the driver.
+
+2. **Run the installation script**:
+
+   Download the installation script:
+
+   ```bash
+   wget https://raw.githubusercontent.com/blakeblackshear/frigate/dev/docker/hailo8l/user_installation.sh
+   ```
+
+   Make it executable:
+
+   ```bash
+   sudo chmod +x user_installation.sh
+   ```
+
+   Run the script:
+
+   ```bash
+   ./user_installation.sh
+   ```
+
+   The script will:
+
+   - Install necessary build dependencies
+   - Clone and build the Hailo driver from the official repository
+   - Install the driver
+   - Download and install the required firmware
+   - Set up udev rules
+
+3. **Reboot your system**:
+
+   After the script completes successfully, reboot to load the firmware:
+
+   ```bash
+   sudo reboot
+   ```
+
+4. **Verify the installation**:
+
+   After rebooting, verify that the Hailo device is available:
+
+   ```bash
+   ls -l /dev/hailo0
+   ```
+
+   You should see the device listed. You can also verify the driver is loaded:
+
+   ```bash
+   lsmod | grep hailo_pci
+   ```
 
 #### Setup